How To Repair A Spring Roller On A Sliding Screen Door

How To: Sliding Screen Door Rollers

Tired of using your screen door every bit office of your practice routine? If so, and so it is time for you to replace your worn-out screen door rollers.

By following these step past pace instructions, we promise to guide you through the screen door roller choice and replacement procedure. After you complete the reading for each step, you should be able to remove your screen door from it'southward track, remove the roller from the door and with your roller in hand, select and purchase the replacement roller from your local hardware store, and then install the new roller and remount your door.

Please retrieve that there are hundreds of door manufacturers, all making four or 5 door models each, so yous need to be prepared for the possibility that y'all may encounter some modest variations from our step-past-stride instructions. If you don't find your roller listed or your roller replacement feel was different than described below, please experience free to write u.s.a. an e-mail and tell u.s.a. about it so we tin can add information technology to our guide.

Here is a video to go along with the step-by-step instructions beneath to help guild you through the process.

Door Removal:
Nearly screen doors use spring-loaded rollers to go on the door from jumping off of the track. First elevator your door up and down in the track. Check if there is enough room to remove your door without adjusting the rollers. If you can remove the door, get to Step ii (Effigy 2). If non, please continue to Step 1 (Effigy 1).

Step 1. By rotating the screwdriver counter-clockwise you tin can lower the door (Figure 1A and 1B)

Pace 2. Use a slotted screwdriver to "popular" the rollers off the track.

Step 3. Now swing the lesser of the door out until you can drib the door downward and out of the top rail. Place your screen door on a worktable or sawhorse.

Step iv. Look into the frame of the door and identify the roller style that you lot demand from the chart below. Follow the specific instructions to remove that manner of roller.

Instance: Every bit with this roller type, y'all tin can run into that a slotted screwdriver is needed to elevator the bound off the adjustment screw (Figure 4A). At present you tin can pull out and replace the roller (Figure 4B).

If This Is Your Roller:

Then Practise This:

If This Is Your Roller:

Then Do This:

Locate and remove the roller mounting screw at the lesser of the door. The screw should exist to a higher place the adjustment screw hole. At present pull out the roller from the door frame, using pliers if needed. This fashion of roller has dimples in the housing to lock the inner housing upward inside the outer housing, to aid with installation. Screw the new roller in and snap the inner frame into the outer frame. Re-hang your door. Once you start turning the adjustment spiral (clockwise), the inner frame volition snap back out.

If This Is Your Roller:

Then Practice This:

The mounting screw for this roller is located at the end of the spring. Remove the spiral with a Phillips screwdriver. Unless you lot needed to back off the adjustment screws to remove the door from information technology's frame you shouldn't need to adjust the height of the new rollers.

If This Is Your Roller:

And then Practise This:

Remove the two (two) mounting screws institute at the bottom of the door. The screws will be on each side of the cycle. Pull the roller out of it'south slot.

If This Is Your Roller:

Then Do This:

With a slotted screwdriver, wedge between the spring cease and the door tab and push off. Then push the spring inward and out betwixt the door tabs. Install the new roller by looping the spring through the tabs and using the screwdriver as a wedge in the opening to snap the spring onto the tab.

If This Is Your Roller:

And so Do This:

Remove the roller mounting screw located on the bottom of the door adjacent to the roller. Brand annotation of the leap's placement and so swing the roller out. Since the adjustment screw stays on the roller, call back to guide the new roller's aligning screw dorsum into identify as you mount the new rollers.

If This Is Your Roller:

And so Do This:

Look into the roller door slot. Yous will meet the mounting spiral at the cease of the leaf spring. With a Phillips screwdriver, remove the screw and pull out the roller. Since the adjustment screw is at the tiptop of the roller, y'all usually do not demand to worry about adjusting your door after replacing the roller.

If This Is Your Roller:

Then Do This:

Loosen or remove the roller mounting spiral that is located nigh 2" from the bottom on the edge of the door. The roller mounting screw is usually found right above the aligning screw hole. At present pull out the roller from its door frame, using pliers if needed.

If This Is Your Roller:

And so Practise This:

Replacing a height-hung screen door'due south rollers may require you to loosen the summit rail rollers with a minor wrench so y'all can lift your door upwards and out of the bottom guide. Swing the door approximately 45 degrees and tilt the door out. With a screwdriver, replace the rollers, mounting the new ones in the same locations.

If This Is Your Roller:

Then Do This:

The roller's mounting spiral is located virtually two" from the bottom, at the edge of the door. Make notation of how the mounting screw is situated between the roller's frame and the top of the ringlet leap. Remove the mounting screw. This function gives the roller the anti-jump characteristic. Pull out the roller through the lesser, using pliers if needed. Slide the new roller into the door aqueduct and and so push button the mounting/adjusting screw in-between the roller housing and spring, through the slot in the door. After you re-mount the door, button the adjustment screw down and tighten it to raise the door.

If This Is Your Roller:

Then Practice This:

Showtime wait into the roller opening and make note of the bound's placement. Remove the roller mounting screw located on elevation of the door frame, to a higher place the roller. Pull out the roller from the bottom.

Step 5. To the hardware store! With roller in manus, compare your roller to our display. First friction match up the roller housing and/or jump shape. Is the roller wheel the same bore and fabric as yours? Changing to a steel or nylon ball-begetting wheel will make your door ringlet easier. If y'all tin't find a match, check with the special lodge desk, equally they should be able to order your replacement rollers for you.

Footstep 6. Install your new rollers the same way y'all removed the one-time ones. There is no need to add any lubricant, every bit it will only attract dirt and dust. Our bearings are greased at the factory.

Pace seven. Elevator your door back into it's top track while tilting the bottom of the door as shut to it'southward bottom runway as you tin can get. While lifting upward, try to go the bottom rollers onto the track. If you are having problems, effort using the slotted screwdriver trick: Lift the door on the border of the wheel with the screwdriver and lever it up and over onto the rail (Figure vii).

Step 8. Here the adjustment screw is on top of the rail (Effigy 8). Unless you needed to drop your door to remove it, you will detect with most installations yous will not need to re-conform your door pinnacle. But, if adjustment is needed, turn screw clockwise to raise that side of the door. Square your screen door in relation to the jamb and check that your latch locks properly at that height. If not, adjust the latch strike first earlier trying to re-adjust the rollers over again (Effigy 9).